Invisible speakers: drywall, glass, wood and what you can apply on top
An invisible speaker turns the wall or glass itself into the loudspeaker, so sound depends on the material and the finish thickness. Here is what manufacturers confirm, what they leave out, and the order of works.
- The exciter makes the surface itself sound; the result depends on the material, its thickness and the finish layer.
- Ekinex Invisible: DRYWALL takes plasterboard up to 16 mm, GLASS up to 12 mm, WOOD 18–25 mm, TWIN is a double exciter.
- Skim coat over the panel: 1.5 to 3 mm depending on the brand; no manufacturer we checked lists tile as an approved covering.
- Bass is limited, so makers offer subwoofers; we found no explicit approval for wet rooms.
- Cable goes in before boarding, the exciter before skim coating, and sound is tested before the final finish.
How it works in plain words
A normal speaker moves a cone; an invisible one vibrates a flat panel: drywall, glass or wood. A small exciter fixed to the back passes vibration into the surface, so the whole panel sounds. Amina calls it turning the entire plastered surface into a sound source.
Two things follow. First, the finish must stay thin: Amina warns that more than 2–3 mm may affect performance. Second, the panel must vibrate freely: Ekinex says WOOD is not for surfaces fixed to the floor or wall and needs a gap of a few millimetres behind.
What Ekinex confirms: material and exciter
Ekinex quotes 40–16,000 Hz for the Invisible Player line, depending on the material. These models are in our catalogue; table data is from the manufacturer's pages.
| Model | Material | What is confirmed |
|---|---|---|
| Invisible DRYWALL EK-DW1-AU | Plasterboard (walls, ceilings) | Up to 16 mm; up to 80 m² per exciter; 120 W max / 40 W RMS; 40–14,000 Hz; 4 ohm; 46 mm deep, 80 mm plate; adhesive EK-3M77-AU |
| Invisible GLASS EK-GL1-AU | Glass and non-porous materials (e-bond, acrylic, lexan, fibreglass) | Up to 12 mm; 120 W max / 40 W RMS; 40–14,000 Hz; 4 ohm; Glassfix tape EK-GFX-AU |
| Invisible WOOD EK-WO1-AU | Wood 18–25 mm | 120 W / 40 W RMS; 40–14,000 Hz; 4 ohm; not for surfaces fixed to floor or wall; a few mm gap behind |
| Invisible TWIN EK-TW1-AU | Double exciter | 240 W max / 80 W RMS; 40–15,000 Hz; 8 ohm; 160 x 80 mm plate |
For vertical plasterboard walls Ekinex offers the Vertfix EK-VFX-AU bracket (sold separately), and for glass an aluminium cable duct, Coverglass EK-CGL-AU. The amplifier is POWER 1 EK-PW1-AU: 200 W RMS into 4 ohm in mono or 2 × 80 W RMS into 4 ohm, for 1, 2, 4 or 8 exciters, with 50 Hz high-pass and low-pass filters; power supply included.
Finish on top of panel-type invisible speakers
The second type is a ready-made panel built into the wall and skimmed over (Amina, Stealth Acoustics, Sonance, Nakymatone, Monitor Audio). We do not stock these brands; the table is a reference to the limits their makers set. The main one: keep the layer thin.
| Brand | Allowed layer | What the manufacturer allows |
|---|---|---|
| Amina | 2 mm; above 2–3 mm may affect performance | Plasters, micro-cement 2–3 mm, veneer, thin stone veneer and marble, leather, fabric, HPL up to 2–3 mm |
| Stealth Acoustics | 1.5 mm (1/16 in) | Four coats of latex paint or light wallpaper; rough textures not recommended |
| Sonance Invisible | Up to 3 mm of topping compound | Drywall, some plasters, wallpaper, leather, veneer |
| Nakymatone | Within about 1.5 mm (1/16 in) | Plaster, wallpaper, laminates, leather, thin wood panels |
| Monitor Audio IV140 | Thickness not stated | Skim coat, then paint, light wallpaper or fabric |
None of the manufacturers we checked lists ceramic or porcelain tile as an approved covering, so do not tile over an invisible speaker. Only Amina lists thin stone veneer and marble. Cerasonar publishes no layer limit. For anything unusual, ask the maker before work starts: Amina itself asks for such materials to be tested.
Limits to know before you buy
- Bass. Ekinex's 40 Hz lower limit depends on the material; Monitor Audio IV140 starts at 75 Hz. Nakymatone, Cerasonar, Sonance and Ekinex all offer subwoofers.
- Amplifier. Brand-specific: Amina panels need an amplifier plus a protection unit, Cerasonar a DSP amplifier with factory presets; Nakymatone panels are passive and accept any amplifier; Ekinex exciters use the POWER 1 with its filters.
- Wet rooms. We found no explicit approval from any manufacturer; Stealth Acoustics warns against leaving an unfinished panel in humidity.
- Substrate. Nakymatone rules out thick stone walls and dense insulation behind the panel.
Order of works during a renovation
- On the wall plan mark where sound is needed and where furniture goes: no exciter behind a wardrobe.
- Choose the system and amplifier; reserve space for the amplifier and a subwoofer.
- Before boarding, run cable to every exciter and label it.
- Mount the exciter per the manufacturer's instructions: Ekinex DRYWALL is fixed with EK-3M77-AU adhesive (the Vertfix bracket holds it in a vertical plasterboard wall), GLASS with Glassfix tape.
- Close the wall and skim thinly, within your brand's limit.
- Before painting, connect the amplifier and play a test track at different volumes.
- Then apply the final finish.
Invisible or ordinary built-in speakers: which suits whom
Invisible speakers suit places where no part may show: a glass partition, a flat ceiling, a wood panel. Ordinary built-ins such as Loxone Install Speaker or Basalte Cielo show a grille, but it can be painted to match the ceiling, and their sound does not depend on finish thickness. A practical split: background music with nothing on show, go invisible; loud music and film, ordinary built-ins plus a subwoofer. See our guide to in-ceiling speakers.
Frequently asked questions
Can an invisible speaker be covered with tile?
No: none of the manufacturers we checked lists tile as an approved covering. They list thin skim or plaster, paint, light wallpaper and veneer; Amina adds thin stone veneer.
How thick can the skim coat over an invisible speaker be?
Stealth Acoustics and Nakymatone say about 1.5 mm, Amina 2 mm (above 2–3 mm performance may suffer), Sonance up to 3 mm.
What drywall works with Ekinex Invisible DRYWALL?
The manufacturer states plasterboard walls and ceilings up to 16 mm thick and “up to 80 m² per exciter”. The exciter is fixed with EK-3M77-AU adhesive.
Do invisible speakers need a subwoofer?
For film and loud music, plan one. Ekinex's stated 40 Hz lower limit depends on the material, Monitor Audio IV140 starts at 75 Hz, and Nakymatone, Cerasonar, Sonance and Ekinex all offer subwoofers.
Can I install invisible speakers in a bathroom?
We found no explicit approval for wet rooms from any manufacturer we checked, and Stealth Acoustics warns against leaving an unfinished panel in humidity. In a bathroom, use an ordinary speaker with a stated IP rating.
Choose exciters and an amplifier
The catalogue has Ekinex Invisible DRYWALL, GLASS, WOOD, TWIN, the POWER 1 amplifier and accessories.