Planning guide

In-ceiling speakers in a smart home: how to plan music room by room

In-ceiling speakers barely show, but the decisions behind them come before finishing: cable and mounting housings cannot be added later. Six steps, from a zone plan to control.

Updated: 20 November 2026 · SmartBee
In short
  • Decide zones and stereo or mono first, models second: the zone count drives cable and amplifier choice.
  • Passive speakers need an amplifier in a panel or rack; active ones have it built in and need power and a data line at the speaker.
  • Cable and mounting housings (concrete, drywall, suspended ceiling) go in before finishing.
  • Loxone's guidance for living spaces with a standard ceiling height: one speaker per 15 m²; put a stereo pair where people sit and listen.
  • For bathrooms and terraces check the IP rating: Loxone Install Speaker 7 and 10 are IP53/54, Satellite Speaker is IP64; confirm the exact spot with the manufacturer.

Step 1. Decide zones and stereo or mono

A zone is a room or part of a room where music plays independently. More zones mean more amplifier channels and cable runs. A living room where people sit and listen needs a stereo pair; a kitchen, hallway or bathroom usually manages with one mono speaker. The table counts are a practical guide, not a manufacturer's rule.

RoomHow many speakersWhat to check
Living room2 (stereo pair); for a large room, Loxone's guidance of 1 per 15 m²Pair symmetric to the listening spot; separate cable to each
Kitchen1–2Steam and grease above the hob: keep away from the extractor, check the IP rating
Bathroom1IP rating; confirm your bathroom zone with the manufacturer and electrician
Bedroom1–2Quiet background level, own volume control, sleep timer
Terrace, covered pergola1–2 outdoor speakersStated IP rating: Loxone Satellite Speaker is IP64; Install Speaker (IP53/54) only for covered outdoor areas; cable in conduit
Tip: Run cable to rooms where you plan no music yet: an extra run in an open wall is far easier than chasing a finished one.

Step 2. Passive speakers with an amplifier, or active

A passive speaker has no amplifier: one in the panel or rack powers it, so only speaker cable runs to each point. The Loxone Audioserver has such an amplifier built in: 4 speaker outputs, Class D, 4–8 ohm, 18 W RMS per channel (50 W is peak power). A Stereo Extension adds one more stereo output.

An active speaker has the amplifier built in. The Loxone Install Speaker 7 Master runs on 24 V and connects over Tree Turbo; one Master drives a chain of up to 20 Client speakers, and Loxone quotes up to 210 speakers per Miniserver. The trade-off: power and a data line must reach the Master, and electronics in a ceiling are harder to reach than a panel.

  • Few zones, all electronics in one place: passive speakers plus an amplifier in the panel.
  • Many zones and a Loxone Miniserver already installed: chained active Master/Client speakers.
  • No way to pull cable: the Loxone Wireless Speaker, which the manufacturer says needs neither wiring nor an Audioserver.

Step 3. Cable and housings before finishing

The housing depends on the ceiling: concrete and drywall hold a speaker differently. Loxone has housings for concrete ceilings and walls (Install Speaker 7 and 10), a backbox for suspended ceilings and a surface box where cutting in is impossible. Basalte Cielo ceiling speakers (C5, C6, C8) have separate housings for drywall and concrete; the in-wall Plano has them for drywall and for brick or concrete.

  1. Mark zones and speaker points on the ceiling plan.
  2. Pick models and housings for your ceiling type: concrete, drywall or suspended.
  3. Pull cable from the panel or rack to each point in one piece, no splices. For passive speakers Loxone specifies cable up to 2.5 mm².
  4. Fix the housing before the pour or the boarding: in concrete it goes into the formwork.
  5. Label both cable ends and photograph the route before it is closed.
Tip: An in-ceiling speaker is not fire-rated on its own. Monitor Audio explains that a fire-rated ceiling needs a fire hood over the speaker, which also reduces sound transmission to the next room. Ask your designer early.

Step 4. Speaker layout

For background music even coverage matters more than power: several speakers at moderate volume sound smoother than one loud one. As a practical guide, not a manufacturer's requirement: keep speakers about 0.5 m from walls, not directly above the sofa or bed head, and place a stereo pair symmetrically to the seat.

Room 4 × 5 m, ceiling 2.6 mstereo pairsofa≈ 0.5 m from wallsamplifier in the rack / panelspeaker cable, one run per speaker
Top view: a stereo pair about 0.5 m from the walls (a practical guide), each speaker on its own cable run from the amplifier.

Step 5. What controls the music

Music should start three ways: from the app, a wall key and a smart home scene (Morning, Leaving). The wall key must work without internet, so the audio server and amplifier sit in the house and streaming services are just one source.

Sourcesstreaming, radio, TV, doorbellAudio server / streamerin the rack or panelMultiroom amplifierin the rack or panelLiving roomKitchenBathroomTerraceControl: wall keypad, app, scenesKNX / Loxone
Multiroom: sources feed an audio server, then amplifier and speakers per zone; control comes from KNX or Loxone.

The Loxone Audioserver supports AirPlay 2, Spotify Connect (Spotify Premium required) and TuneIn, and the same speakers play the doorbell, alarm clock and alarm signals. Ekinex Sentio has its own app with zone grouping; the KNX-Sentio Gateway turns each zone's volume and play/pause into KNX group addresses for a wall key.

Step 6. What we stock

  • Loxone: Audioserver, Install Speaker 7 and 10 (Master, Client, Passive), Satellite Speaker IP64, Wireless Speaker, housings for concrete and suspended ceilings.
  • Ekinex: built-in series for drywall (Q10CG, Q15CG, T18CG, ceiling SP525-AU) and masonry (Q15M), Sentio streamer amplifiers, built-in subwoofers.
  • Basalte: ceiling Cielo (C5, C6, C8) with housings for concrete and drywall, in-wall Plano R3 and R5.

The full range is in Speakers and amplifiers. Before buying, match passive speakers to the amplifier by impedance (ohms) and power in the datasheets. Mid-renovation, sort out housings and cable first, then the finish.

Frequently asked questions

How many in-ceiling speakers does a room need?

Loxone's guidance for living spaces with a standard ceiling height is one speaker per 15 m². In practice a living room gets a stereo pair; a kitchen or bathroom usually needs one.

Are passive or active in-ceiling speakers better?

Neither is better outright. Passive speakers need an amplifier in the panel or rack but leave no electronics in the ceiling. Active speakers have it built in but need power and a data line; Loxone Master/Client speakers are chained.

Can I put an in-ceiling speaker in a bathroom?

Check the IP rating: Loxone Install Speaker 7 and 10 are IP53/54, Satellite Speaker is IP64. Confirm your bathroom zone with the manufacturer and your electrician.

What if I can no longer run cable?

Go wireless: the manufacturer says the Loxone Wireless Speaker needs neither wiring nor an Audioserver. If finishing has not started, still run cable so any built-in speaker stays possible.

Do I need a fire hood for an in-ceiling speaker?

Monitor Audio notes that an in-ceiling speaker is not fire-rated on its own, and a fire hood also reduces sound transmission to the next room. Your design and the ceiling's fire requirement decide whether you need one.

Choose speakers and an amplifier

The catalogue has in-ceiling speakers, housings, audio servers and streamers from Loxone, Ekinex and Basalte.

Browse audio

Read next

Loading...
Back to top